Care & Cleaning Guide

Practical guidance for maintaining surgical instruments and hospital furniture, helping preserve their appearance, functionality and service life.

Safety noticeThese pages provide general care and maintenance information. Always follow the product-specific Instructions for Use, the instructions supplied by the relevant equipment manufacturer, applicable standards and your healthcare facility's infection-prevention procedures.

Section A · Surgical Instruments

Surgical Instruments – Care, Cleaning & Maintenance

Careful handling, prompt cleaning and regular inspection help reusable stainless steel instruments keep their finish and function.

Hospitime instruments are supplied non-sterile. Clean and sterilise them before first use, following the product IFU.

Surgical Instruments – Care and Cleaning

  1. Handle with care

    • Place instruments down. Do not drop or throw them.
    • Protect tips, teeth and cutting edges.
    • Keep delicate and microsurgical instruments separate.
    • Do not pile heavy instruments on top of light ones.
    • Use each instrument only for its intended purpose, never as a lever.
    • Carry contaminated instruments in a closed container.
  2. Initial cleaning at the point of use

    Cleaning must come before disinfection or sterilisation. Organic and inorganic material left on an instrument interferes with these processes.

    • Wipe off visible soil as soon as possible after use.
    • Do not let blood or tissue dry on the instrument.
    • Keep instruments moist until cleaning, using the method your facility approves.
    • Open hinged instruments and take apart any that the IFU says can be disassembled.
  3. Cleaning methods

    Manual cleaning

    Use soft brushes and lint-free cloths. Clean below the water surface to limit splashing, and brush hinges, serrations and lumens.

    Ultrasonic cleaning

    Use where the IFU allows. Open hinged instruments fully and do not overload the basket.

    Washer-disinfector

    Use the validated cycle your facility has approved. Load instruments so all surfaces can be reached.

    Detergents: use a detergent compatible with the instrument, at the dilution, temperature and contact time given by the detergent manufacturer. Neutral pH detergents usually give the best material compatibility. Use enzymatic cleaners as their manufacturer directs.
  4. Rinse and dry

    • Rinse thoroughly to remove all detergent residue.
    • Use water of the quality your facility specifies for rinsing.
    • Dry completely, paying attention to hinges, box locks and lumens.
    • Do not leave instruments wet. Moisture can lead to staining.
  5. Surgical Instrument Inspection and Maintenance

    Inspect every instrument after cleaning, preferably under magnification and good light. Remove any damaged or worn instrument from service.

    • Corrosion: rust, pitting or stains
    • Damage: bent tips, burrs or nicks
    • Cracks: especially around box locks and hinges
    • Wear: worn serrations, teeth or coatings
    • Jaws: they close fully and meet evenly
    • Misalignment: tips line up when closed
    • Hinges: they move smoothly, without stiffness or play
    • Ratchets and cutting edges: they hold and cut as intended
    Tips & jaws Box lock / hinge Ratchet
  6. Lubrication, only where specified

    Lubricate hinges, box locks and moving parts only when the product IFU calls for it. Use an instrument lubricant suited to the sterilisation method, as directed by the lubricant manufacturer. Do not use general-purpose oils.

  7. Cleaning and Sterilisation Guidance

    Step 1Cleaning

    Removes visible soil and organic material. It is required before any disinfection or sterilisation.

    Step 2Disinfection

    Kills many or all pathogenic microorganisms, but not necessarily bacterial spores.

    Step 3Sterilisation

    Destroys all forms of microbial life, including spores, by a validated process.

    Sterilisation parameters are not given here. Use the method and cycle specified in the product IFU, the sterilizer manufacturer's instructions, applicable regulations and your facility's validated procedures.
    • Store instruments clean, dry and protected from damage.
    • Use trays or racks that keep instruments apart. Do not overcrowd them.
    • Protect sharp tips and cutting edges in storage.
    • Keep sterile packs in clean, dry storage as your facility requires.
Section B · Hospital Furniture

Hospital Furniture – Care, Cleaning & Maintenance

Beds, trolleys, stools and cabinets combine several materials. Clean each one with a product its manufacturer approves, and check moving parts regularly.

Hospital Furniture – Care and Cleaning

Stainless Steel and Powder-Coated Surface Care

Use cleaning and disinfecting products approved by your facility and compatible with the surface. Follow the product manufacturer's instructions for dilution and contact time.

Stainless steel

  • Wipe with a soft cloth and a mild, compatible cleaner.
  • Wipe along the grain of brushed finishes.
  • Rinse off residue and dry to avoid water marks.
  • Do not use steel wool or wire brushes.

Powder-coated / painted

  • Use a damp cloth with a non-abrasive cleaner.
  • Dry after cleaning.
  • Check for chips and scratches that expose the base metal.
  • Report coating damage so it can be repaired.

ABS / plastic parts

  • Clean with a soft cloth and a cleaner compatible with plastics.
  • Avoid solvents unless the manufacturer approves them.
  • Check panels and end boards for cracks.

Upholstery & mattress covers

  • Clean and disinfect covers with products the cover manufacturer approves.
  • Do not soak covers or let fluid pool on them.
  • Inspect for tears, punctures and fluid ingress.
  • Replace damaged covers.
MOTOR
Electric beds

Electrically operated beds and equipment

  • Never immerse, hose down or pressure-wash electrical furniture.
  • Follow the manufacturer's instructions on disconnecting from mains power before cleaning.
  • Use a cloth that is damp, not wet. Protect motors, control boxes, hand controls and connectors from fluid.
  • Check cables, plugs and hand controls for damage.
  • Electrical inspection and repair must be done by qualified personnel only.
Moving parts

Hospital Bed and Trolley Maintenance

Wheels, castors and brakes

  • Remove hair, thread and debris from castors.
  • Check that wheels roll and swivel freely.
  • Check that brakes lock and release fully.
  • Check castor fixings for looseness.

Mechanisms and moving parts

  • Check side rails latch securely.
  • Operate backrest, knee rest and height adjustments through their full range.
  • Check crank handles, IV pole sockets and accessories.
  • Lubricate moving parts only as the manufacturer specifies.
  • Remove the item from use if any part does not work as intended.
Checklist

Routine Inspection Checklist

Tick each item as you check it. Ticks are not saved.

Cleaning frequency

Example Cleaning Frequency Framework

An example of how a schedule could be organised. Set your actual schedule by your facility's infection-prevention policy and the product IFU.

Example only · not mandatory
ItemExample timingExample activity
Surgical instruments
Reusable instrumentsAfter every usePoint-of-use care, cleaning, rinsing, drying and inspection
Reusable instrumentsBefore every useSterilisation by a validated process, as the IFU specifies
Hinged instrumentsAs the IFU specifiesLubrication
Hospital furniture
High-touch surfaces (rails, controls)Daily and between patientsCleaning and disinfection with approved products
Whole bed, trolley or stoolWhen a patient is dischargedFull cleaning of all surfaces
Castors and brakesWeeklyDebris removal and function check
Mechanisms and electrical partsPeriodically, per manufacturerInspection by trained or qualified personnel

Swipe the table sideways to see all columns.

What to avoid

What to Avoid

Surgical instruments

  • Letting blood or tissue dry on instruments
  • Steel wool, wire brushes or abrasive powders
  • Bleach or chlorine-containing products, unless the IFU permits them. They can corrode stainless steel.
  • Leaving instruments to soak in saline
  • Detergents not intended for instruments, or used outside their manufacturer's directions
  • Leaving instruments wet after rinsing
  • Dropping, piling or overloading trays
  • Using instruments as levers or for unintended tasks

Hospital furniture

  • Hosing, pressure-washing or soaking electrical furniture
  • Abrasive pads or scouring powders on coated or stainless surfaces
  • Solvents on plastics or upholstery, unless the manufacturer approves them
  • Letting fluid pool on mattress covers or near controls
  • Mixing cleaning chemicals
  • Loading beyond the rated safe working load
  • Using furniture with faulty brakes, rails or mechanisms
Downloads

Printable Checklists

Print a checklist or save it as a PDF. These are general checklists, not Instructions for Use.

Surgical Instrument Care Checklist

Handling, cleaning, drying, inspection and storage checks.

Hospital Furniture Cleaning & Maintenance Checklist

Surface cleaning, electrical safety, castors, brakes and mechanisms.

References

References

Need the IFU or Care Details for a Product?

Send us the product name. Our team will share the care information available for that item.

Send an Enquiry